Most Recently Updated Threads
StreetRodding.com is proud to have the following Advertisers supporting this site.
- November 20, 2009 03:15 PM in General DiscussionsI have the chance to buy a known 700R from a friend. This transmission was in a built 32 Ford with a 383 Roller and 4:11 gears. It has been in the car from day one, and has worked fine for 5 years. Talking with him about this, he said it had no 12 volts for the lockup. So it has to be locking on pressure I assume. Somebody tell me how this works, and is this a good bad or ugly way to do it.Last Updated 11/20/2009 03:29 PM
- anybody own and operate one of these ? Updated: November 14, 2009 08:10 PM roughly what is the cost without the plasma cutter and computer.Last Updated 11/20/2009 02:58 PM
- November 19, 2009 03:35 PM in General DiscussionsWe have asked our friend Bennie to think about a design for a new SR shirt, but we need a few other designs for use on a new page Eriq is working on. Any artist want to give it a try? You get the same pay Eriq and Al get (undying gratitude) and the opportunity to tell people "I did that!" We can let the masses chime in on which one is "The Look" and may end up using several around the site. Look at our StreetRodding.com logo and give us an improved version with a cool Street Rod!... Read All ...Last Updated 11/20/2009 02:53 PM
- November 19, 2009 10:49 AM in General DiscussionsIn what way do you put your car up for the Winter(cold climates)? With snow,ice and salt I never drive my car during this time.I lay down 5/16" particle board 4'X8'----4 sheets on the concrete garage floor. This isolates the tires and undercarriage from the cold and moisture. I do not put the car on jacks in the event I need to move the car.I add Stabile to the gas. I don't keep the tank full. Usually 1/2. Not sure if this is a good idea because of condensation inside the tank??I'd appreciate your i ... Read All ...Last Updated 11/20/2009 02:40 PM
- November 11, 2009 07:41 PM in General DiscussionsI can't do much on my 37 Ford for now. Waiting for a new floor to come. So I have been thinking about something else I will still need to get and do. The wind sheild wipers came to mind. Now with money not in my pocket much for quite a while. I have to think of other ways of doing things. Now it would take at least a couple of years to save up enough to pay for a new Newport hookup, so I started thinking of what might do the same job, but be a whole lot cheaper. How about the wiper motors out of a couple of ... Read All ...Last Updated 11/20/2009 12:25 PM
- November 15, 2009 10:36 PM in General DiscussionsIs there anyone who makes after market steel dashes for '37 Fords? I'm looking for a dash extension really, and I can make one, just wondering if there are any premades to look at. Thanks, BillLast Updated 11/20/2009 10:58 AM
- November 19, 2009 10:41 AM in General DiscussionsCool new shirt, I wish I knew where to get one!Last Updated 11/20/2009 10:19 AM
- November 18, 2009 10:00 AM in General DiscussionsJust a thought for you guys.I did this last year and plan on doin it again.Go to your local V A Hospital, and invite a few of the vets over for the day, stuffin yer self and just good times.I had 3 guys over last year and they really enjoyed it.Goin over today and invite a few more this year.Ain't that what "Thanksgiving Day" is aboutGIVINGLast Updated 11/20/2009 09:00 AM
- November 19, 2009 09:14 AM in General DiscussionsI swap out rear ends on my truck ,with a 4x4S-10,posi 3:71gears,disc brakes,the universal joint fits the yoke but is too narrow,is there a universal joint i can replace on the drive shaft for the right fit ? the drive shaft is off a camaro and so was the rear end ,S-10 yoke is biggerLast Updated 11/20/2009 07:44 AM
- November 20, 2009 12:06 AM in General DiscussionsAnybody out there have any info on 1965 Econline wiring, diagrams etc?ThanksLast Updated 11/20/2009 12:06 AM
- November 19, 2009 11:58 AM in Tech TipsJust a reminder as I see these questions all the time.If you need transmission dimensions,ratios etc. go to- summitracing.com,then click on expert advice, then type in transmission dimensions in the search window.It'll show GM,Ford,Mopar trans pics, measurements and ratios for the popular trans. Summit has alot of other helpfull info too.Last Updated 11/19/2009 11:08 PM
- November 19, 2009 09:41 PM in General DiscussionsGoing to be in Cheyenne probably sometime Saturday to pick up an El Camino with a friend of mine--any one in the area that might want to grab a burger and meetLast Updated 11/19/2009 09:41 PM
- November 18, 2009 10:13 PM in General DiscussionsDon--they were among us this afternoon---I started the thread but not under Uncle Bills name--don't know what happened there.Anyway--going to put power antenna in wife's 48. Any recommendations as to what brands to use or stay away from. Wires are all run--been looking at the Autoloc system--EBAY, Yogi's etc. Did a search here and found nothing. thanksLast Updated 11/19/2009 12:12 PM
- November 17, 2009 08:36 PM in General DiscussionsHaven't seen Robert lately.... is it me or is he awol...Last Updated 11/19/2009 10:46 AM
- November 19, 2009 09:03 AM in General DiscussionsLast Updated 11/19/2009 09:03 AM
- November 17, 2009 09:09 PM in General Discussions
Just want to share a "Photo op" I had today when visiting a friend. I HAD to take a couple pictures in his KOOL backyard. The bike is neat too ! (check the make) Last Updated 11/19/2009 08:12 AM - November 18, 2009 03:53 PM in Q&AIs the yoke for a 350 trans the same as a 700r4?Last Updated 11/19/2009 08:05 AM
- November 17, 2009 08:01 PM in General DiscussionsI'm going to be in Nashville from wed nite thru Sun morning if you want to get together for coffee. I won't have wheels and I'm staying at the Holiday Inn on McGavock Pike. My cell is 505.220.1600SteveLast Updated 11/18/2009 10:36 PM
- November 18, 2009 03:21 PM in General DiscussionsLast Updated 11/18/2009 03:37 PM
- November 18, 2009 11:02 AM in General Discussions
I recently received these pics in a email and thought that you all would enjoy them. Last Updated 11/18/2009 03:34 PM
