Each member has their own Blog on StreetRodding.com that can be accessed at blogs.StreetRodding.com/yourUserName. Read the online journals of other StreetRodding.com members, pick up tips and secrets from the pro's, ask questions of the rodding community or just tell us what's going on in your neck of the woods!
|
| Rear end ratios
|
|
OK.....I think I must be getting senile, or just slow. Anyway, I wanted to check the rear ratio on the roadster. Jacked it up, put trans in neurtal, marked the tire, had my bride rotate the tire while I counted the turns on the driveshaft which I also |
| 07/16/2008 09:31 AM |
General Discussions |
Comments (10) |
| Ideas on seat belt lengths
|
|
I'm getting ready to order the lap belts for the 32. Not sure which lenght to use--60" or 75" belts. We're going with lift latch belts, non retractable. Any input is greatly appreciated. |
| 05/14/2008 08:38 AM |
General Discussions |
Comments (6) |
| 3 point belts
|
|
Has anyone out there installed Juliano's (or other) 3 point belts in a roadster? I need to put belts into my new ride and want to use 3 point if possible. |
| 04/21/2008 05:27 PM |
General Discussions |
Comments (16) |
| Help identifying a SBC
|
|
Have a SBC, know it's a 350 because it has "5.7LG" on the upper driver's side of the block. Rear side of the top of the block has "143736" and "J086". Questions are....anyone know what the G means? Also trying to determine if it's a 2 or 4 bolt, possi |
| 04/20/2008 08:03 PM |
General Discussions |
Comments (23) |
| Ideas on pricing.
|
|
Guys, I'm thinking of selling my 37 but frankly don't know what to price it. Early Gibbons body on a fully boxed original 36 frame. 94 Firebird LT1 with March pulley system and 4L60E trans, 9" ford rear, air ride, PS, PA remote doors, decent to very go |
| 11/11/2007 01:39 PM |
General Discussions |
Comments (1) |
| Carb Question
|
|
Finally got the 37 running this past weekend. Good to hear that LT1 fired up again. On another topic, however, can anyone tell me how to ID a Holley carb. I think the one on the vette is way oversized, but I'd like to figure out what I have before I lo |
| 07/25/2007 07:09 PM |
General Discussions |
Comments (7) |
| Our Down Under Friends
|
|
Watching the Weather Channel this morning in the hotel and saw how bad the weather is in Australia. You guys all OK down there? |
| 05/24/2007 10:48 PM |
Q&A |
Comments (12) |
| Power Window Question
|
|
A question for the electrical guru's out there. The driver's side power window on my 74 Corvette is stuck in the down position. The window worked fine on Saturday when I went out cruising. I parked the car in the garage with the window in the down posi |
| 05/12/2007 05:33 AM |
General Discussions |
Comments (7) |
| Daddy, It followed me home. Can I keep it?
|
|
Not being able to work on the 37 has forced me to go to something else for cruising. Drove this home from Quakertown on Saturday. Never owned a vette, always wanted one.....now I have one. I'm sure I'll be asking a ton of questions. Not a street rod b |
| 04/15/2007 08:14 AM |
General Discussions |
Comments (0) |
| 2nd LT1 question
|
|
Have to run the steam line from the back of the heads. Rather than run the line to the top of the radiator tank and having a new fitting installed into the tank, would it work if we run the steam line to the overflow tank feed line? What about |
| 02/17/2007 07:52 AM |
Q&A |
Comments (4) |
| Thanks
|
|
Tomorrow is Veterans Day, observed. A heartfelt thanks to all who served and are serving their country. And Lord, Please hold those in harms way safe. |
| 11/10/2006 08:56 PM |
Q&A |
Comments (17) |
| Someone to look @ a car
|
|
Anyone in the Charleston, SC area willing to take a look at a car for me? Just want to make sure it's not a rolling rust bucket, screwed up frame, etc. Thanks |
| 10/03/2006 12:35 PM |
Q&A |
Comments (6) |
| Fuel Line Question
|
|
What are your thoughts on running flexible fuel line from tank to filter to injectors? I have to re-route the fuel lines on the 37 to get them away from the exhaust. Currently 3/8" aluminum tubing. There are also two kinks in the line |
| 08/30/2006 07:57 AM |
Q&A |
Comments (7) |
| 4L60E Question
|
|
Hope to get a little direction here. Been pretty slow on the 37 due to health problems but still doing what I can. Have the LT1 all running right and got it all buttoned back up, and took it out for a short (about 5 mile) test run last night.& |
| 08/26/2006 10:00 PM |
Q&A |
Comments (8) |
| Macungie
|
|
I know carpro is going to Macungie this weekend. Anyone else out there going to attend. Not sure if the 37 will be there or not, but I'll be there if only as a spectator. We should all try to meet up if possible. |
| 08/24/2006 08:39 AM |
Q&A |
Comments (2) |
| Checking In
|
|
Just checking in to see how our TX and Mid-west folks are holding up with the crazy weather and wild fires. Let us all know you're all OK |
| 03/16/2006 10:15 AM |
Q&A |
Comments (18) |
| Maple Grove Swap Meet
|
|
Anybody planning on attending the Maple Grove Swap Meet this Saturday (3/18) ? |
| 03/13/2006 10:38 AM |
Q&A |
Comments (3) |
| Evaporator Mount
|
|
I'm ready to mount the evaporator for my AC. Fiberglass body, smooth firewall. I've thought about glassing brackets to the interior side of the firewall and then using them to mount the evaporator. Just want to check to make sure glassin |
| 02/25/2006 07:30 AM |
Q&A |
Comments (4) |
| Info on 34 coupe
|
|
I picked up a chopped and channeled 34 5 window coupe in North Carolina a while ago. Yellow, w/flames, small block ford and c4 trans, tilt fiberglass front end, steel body. Trying to get more info on the car. Reported to have been a Stre |
| 01/28/2006 05:54 AM |
Street Rods Wanted! |
Comments (4) |
| New Wheel Care
|
|
Any thoughts on what to use on new aluminum wheels. They have an excellent finish and shine extremely well. I don't want to use the Zoops coating since it slightly reduces the shine. Was thinking of waxing them to seal the aluminum |
| 01/16/2006 10:10 AM |
Detailing Tips |
Comments (19) |
