Each member has their own Blog on StreetRodding.com that can be accessed at blogs.StreetRodding.com/yourUserName. Read the online journals of other StreetRodding.com members, pick up tips and secrets from the pro's, ask questions of the rodding community or just tell us what's going on in your neck of the woods!
|
| 200 4R trans
|
|
bolting to cross member |
| 10/25/2008 11:25 AM |
General Discussions |
Comments (11) |
| mechanical fans vs electrical fans
|
|
which on is better for high horse power motor , chevy big block |
| 05/24/2008 11:07 PM |
General Discussions |
Comments (9) |
| Electrical water pump vs mechanical water pump
|
|
which one is better |
| 05/12/2008 11:33 AM |
General Discussions |
Comments (7) |
| ignition recommendations
|
|
ignition system for 540 cu-in |
| 03/01/2008 04:39 PM |
General Discussions |
Comments (2) |
| 700-R4 non lock up tranny
|
|
tranny will not shift in high rpm from 2 to 3rd , and 3 rd to 4th. |
| 12/31/2007 10:52 PM |
General Discussions |
Comments (6) |
| Front brake will not bleed
|
|
Brake will not bleed |
| 12/11/2007 01:30 PM |
General Discussions |
Comments (11) |
| Upgrading Rear breake
|
|
Changed rear brake to disk brake |
| 12/01/2007 09:47 AM |
Tech Tips |
Comments (3) |
| Exhaust system for 78 camaro
|
|
Looking for stainless steel exhaust system for 1978 camaro |
| 06/29/2007 11:25 PM |
Q&A |
Comments (2) |
| Big block chevy cylinder heads
|
|
I have a big block chevy engine with with 119 cc combustion champer and 350cc intake runner. Competition cam 725/ 756 lift and 92/97 deg. durations, 100 deg lope seperation. The valve has a sign of hitting each other ( intke and exhaust) .This is the seco |
| 06/25/2007 10:52 PM |
General Discussions |
Comments (3) |
| Rear chassis and rear end for 1978 Camaro
|
|
I am building a high horse power motor around 1000 hp. This scraemer will go in 1978 camaro. I am looking for complete rear section of frame and narrower rear end that will be fitted that required the least amount of welding possible. It deos not matter i |
| 05/01/2007 06:36 PM |
General Discussions |
Comments (12) |
| Gear Vendors
|
|
Does any body knows where to by gear vendors units? I sent them few emails but they do not replay. |
| 01/15/2007 11:57 AM |
Q&A |
Comments (2) |
| hard shifting 700 R4
|
|
Gentelmen.First happy new year to everybody.Can anyone tell me what is the difference between 4L60 and 4L80 tranny.?Is non lock up better than computer contolled lock up?and which one can handle high horse power engine 1000-1200 hp. |
| 01/01/2007 12:22 AM |
Q&A |
Comments (2) |
| 700-R4 non lockup
|
|
I have a 700-r4 non lockup tranny . I have purchased and installed the 2 bracket required form holley , adjuster holding bracket and end end cable connection bracket, since the carb is holley.I have noticed that there is about 1/8" slack on the cable. The |
| 12/13/2006 08:50 AM |
Q&A |
Comments (1) |
| Procharger supercharger
|
|
Gentelmen . i am putting togther a BBC . I have searched world products and eagle rotating assembaly for 4.5" bore and 4.5" stroke kit for max. comp of 8:1 with 119cc cylinder heads and 9.8" deck hight for supercharged engine , i could not locate |
| 11/11/2006 03:52 PM |
Q&A |
Comments (1) |
| 1.6 rocker ratio on small block chevy
|
|
I just cahnged the rocker arm ratio on my small block from 1.5 to 1.6 , both on intake and exhaust.Hoping to gain about additional 10 HP.The engine is 350 bored .060 over .And 200 cc sprtsman cylinder head , crane solid roller cam The came range is up |
| 10/25/2006 10:55 AM |
Q&A |
Comments (0) |
| Big Block Chevy
|
|
I just finished rebuilding 496 BBC. 11:5 comp. ratio , world cylinder head, Holley HP 870cfm, crane cam 596/596 lift with 296/296 duration ,MSD 6AL, MSD dist (used). Holley mechanicl fuel pump , timing @32 total , when checked timing there was flactuiatio |
| 10/12/2006 06:43 AM |
Q&A |
Comments (6) |
| Fitting transmission in 78 camaro
|
|
I have 1978 camaro , with 400 cu-in beefed up with all the goodies including 177 cu-in wienad buffer.The trany is 350 turbo hydro.I m buying a 1998 camaro- Z28 tranny. I dont know if its 700 or not. I know for sure , its stock tranny that came wit |
| 09/25/2006 11:56 PM |
Q&A |
Comments (3) |
| Weight of the camaro
|
|
Gentelmen , can any one tell me what is the weight of 1978 camaro and 1983 camaro , its important to figure out horsepower on G-tech guage.Thanks |
| 11/26/2005 11:21 PM |
Q&A |
Comments (3) |
| setting up ring and pinion gear on 8.5 chevy
|
|
Gentelmen.I'm in the process of replacing the gear ratio on my camaro from 4.10 to 3.51.My questions is .The pinion gear both the old one and the new one has 2 different checking distance , the old gear has 2.834 and new one is 2.752 |
| 06/12/2005 11:03 AM |
Q&A |
Comments (1) |
| GMC vortech engine
|
|
Gentelmen , I have been reading about the new generation engines ,LS1,LS2,LS6 so on and how much power and torque they produce out of the factory. Can anyone tell me what is the different between the GMC vortech engine and the LSs generation engin |
| 04/20/2005 10:53 AM |
Q&A |
Comments (2) |
